Torque Settings
- Details
- Written by alan
- Hits: 347
A pretty comprehensive list of torque settings.
| Item | ft/lbs | Nm | in/lbs |
| General | |||
| Spark plugs | 11-17 | 132-204 | |
| Engine oil drain plug (19mm) | 22-30 | 31-41 | |
| Gearbox drain plug (24mm) | 29-43 | 35-59 | |
| Gearbox fill plug (square) | 18-29 | 25-39 | |
| Differential drain plug (24mm) | 29-40 | 39-54 | |
| Differential fill plug (23mm) | 29-40 | 39-54 | |
| Wheel nuts | 66-86 | 89-117 | |
| Suspension | |||
| Swaybar bushing bolts | |||
| Front | 13-20 | 18-26 | |
| Rear | 14-21 | 20-28 | |
| Swaybar end link bolts | 27-40 | 36-54 | |
| Upper shock mount plate bolts | 22-27 | 29-36 | |
| Upper shock nuts | 23-34 | 31-46 | |
| Lower shock bolt | 54-69 | 73-93 | |
| Lower control arm bolt, front | 54-69 | 73-93 | |
| Spindle (vertical) bolt | 54-68 | 73-93 | |
| Camber adjustment bolts (D or H-style) | |||
| Front | 69-83 | 94-112 | |
| Rear | 54-70 | 73-95 | |
| Brakes | |||
| Front/rear bracket bolts | 36-51 | 49-69 | |
| Caliper bolts | |||
| Front | 58-65 | 78-88 | |
| Rear | 25-29 | 34-39 | |
| Front/rear banjo bolts | 16-22 | 22-29 | |
| Rear adjuster plug bolt | 9-12 | 12-16 | |
| Engine & Cooling | |||
| Crank pulley bolt (1990 - early 1991) | 80-87 | 108-118 | |
| (plus Loctite 242-blue) | |||
| Crank pulley bolt (late 1991 - present) | 116-122 | 157-165 | |
| (plus Loctite 242-blue) | |||
| Cam cover bolts (must be done in correct order) | 43-78 | ||
| Alternator mounting bolt | 27-38 | 43-78 | |
| Alternator tension adjustment bolt | 14-19 | 19-25 | |
| Water pump - 4 bolts to block | 14-19 | 19-25 | |
| Water inlet pipe - 2 bolts to water pump | 14-19 | 19-25 | |
| Radiator - upper bolts | 14-19 | 19-25 | |
| Thermostat cover - 2 bolts | 14-19 | 19-25 | |
| Timing belt tensioner bolt & idler pulley bolt | 28-38 | 38-52 | |
| Timing belt cover bolts | 14-18 | 19-24 | |
| Cylinder head bolts (must be done in stages and in correct order.)*** | 56-60 | 76-81 | |
| Intake / Exhaust | |||
| Airflow meter bolts | 69-95 | ||
| Intake manifold bracket | 27-40 | 36-54 | |
| O2 sensor by feel as close to | 22-36 | ||
| Exhaust pipe clamp bolt (to bell housing) | 15-20 | 21-27 | |
| Bell housing bolts | 48-65 | 65-88 | |
| Exhaust header nuts | 28-34 | 38-46 | |
| Cat converter nuts (both ends) | 30-41 | 40-55 | |
| Clutch | |||
| Transmission front cover bolts | 14-18 | 19-24 | |
| Flywheel bolts | 71-75 | ||
| Pressure plate bolts | 14-19 | 19-25 | |
| Bell housing bolts | 48-65 | 65-88 | |
| Prop shaft nuts | 20-22 | 27-30 | |
| Power plant frame bolts | 77-91 | 104-123 | |
| Starter motor bolts | 28-38 | 38-51 | |
| Starter motor mounting bracket bolts | 28-38 | 38-51 | |
| Slave cylinder fluid tube | 113-190 | ||
| Slave cylinder mounting bolts | 12-16 | 16-22 |
These settings may not be correct. Please use with caution.